- How much is Molex worth?
- What does Molex stand for?
- What is a Molex connector used to power?
- Do I need a Molex connector?
- Where does Molex plug into?
- How do I connect Molex fans to PSU?
- Why is Molex still used?
- Does it matter what SATA port I use?
- What is the function of 4 pin Molex connector?
- Why is Molex bad?
- How much power can a SATA cable support?
- What is SATA power connector?
- What is a floppy connector used for?
- Where do you plug SATA?
- How many Molex connectors can you chain together?
How much is Molex worth?
The $7.2 billion purchase of Molex Inc..
What does Molex stand for?
disk drive connectorsMolex connector is the vernacular term for a two-piece pin and socket interconnection, most frequently disk drive connectors. Pioneered by Molex Connector Company, the two-piece design became an early electronic standard.
What is a Molex connector used to power?
Certain Molex connectors are used for providing power to the motherboard, fans, floppy disk drive, CD/DVD drive, video card, some older hard drive models, and more. Compatible connectors are available from many manufacturers, not just Molex and AMP.
Do I need a Molex connector?
Molex connectors are necessary when you don’t have any 3 pin headers left on your board to connect fans. Then you use molex connectors to connect the fans to your power supply rather than the motherboard.
Where does Molex plug into?
If your PSU came with a molex cable, then one of the ends should be able to plug into the PSU.
How do I connect Molex fans to PSU?
To do this, plug the fan into your computer’s power supply. The fan will contain either a male or female Molex connector, and sometimes both. The male connector is larger and slides over the female connector. If your fan has both types of connectors, you need only connect one of the two to the power supply.
Why is Molex still used?
And the likely reason they include the Molex is because PSU makers are keeping them on the PSU. Case fans offer Molex to PC case fan adapters, but you can plug them into the motherboard headers. Or just bung in the box with the PSU SATA Power to Case fan adapters.
Does it matter what SATA port I use?
In terms of general use, no, it makes no difference. Every SATA port is controlled separately and they all get the same amount of love and attention from the motherboard… In summary, for data drives (or any non-bootable drive) it makes no difference at all which port you connect to.
What is the function of 4 pin Molex connector?
Often refers to the 4-pin connectors used to attach DC power to the drives inside a PC cabinet. Molex is a large manufacturer of electronics plugs and sockets that dates back to the 1940s.
Why is Molex bad?
They’re large and clunky and frequently poorly manufactured. Also, there’s not much new hardware that needs them anymore. Molex connectors are legacy, the only reason power supplies still have them is because there’s old components that still use it. …
How much power can a SATA cable support?
54 wattsSATA is rated for 54 watts/4.5 amps. – Do not convert from SATA to Molex/6-pin, this will cause an overdraw and could result in a fire.
What is SATA power connector?
The SATA 15-pin power supply connector is one of the standard peripheral power connectors in computers. It’s the standard connector for all SATA-based hard drives and optical drives. SATA power cables protrude from the power supply unit and are meant to reside only inside the computer case.
What is a floppy connector used for?
the four-pin polarized Berg connectors used to connect 3 1⁄2-inch floppy disk drive units to the power supply unit, usually referred to as simply a “floppy power connector”, but often also referred to as LP4.
Where do you plug SATA?
SATA uses simple cables that are keyed to fit on the drive and motherboard connector one way. Connect one end of the SATA cable to the drive, and the other end to an available SATA port on your motherboard, and you’re halfway there. Some SATA data cables come with L-shaped ends, which can help keep cables tidy.
How many Molex connectors can you chain together?
Splendid. Hmmmm… to take a guess (being safe that is), typically you would have 2 or 3 4pin molex on one rail, which would can hook up 2 HDs and 1 DVD/CDROM. Basically that would be around 20-30W per HD or DVDROM.